DH_Series_InstallESL
Electromagnetic
Door Holder
Assembly Instructions &
Electric Configurations
Part Number 13047
Wall
Door
Recessed Mounting
II. Electromagnet Mounting
Surface Mounting
Flush Mounting
Example:
4" overall distance use
1" extension 4"
10.2 cm
90°
I. Wiring Instructions
This product is a high quality electromagnetic holding device
intended for use in fire door applications.
CLH
CLH CLH
CLH CLH
Low Voltage Application
Model Voltage DC AC Terminals
DHX*-1224 12V 30mA 30mA C and L
24V 30mA 30mA C and H
DHX*-24120 24V 15mA 15mA C and L
120V — 15mA C and H
DHX*-24220 24V 15mA 15mA C and L
220V — 15mA C and H
Performance Data
* X= F— Flush Mount
R— Recessed Mount
S— Surface Mount
Voltage References
C= common
L= low
H= high
High Voltage
Low Voltage
High Voltage Application
Note:
When using models DHX-24120 or DHX-24220
(see chart above) attach green wire to earth ground.
ULÒ
LISTED UNDERWRITERSLABORATORI ESOFCANADALISTEDBY
FM California State Fire Marshal Approved
MEA (New York City)
APPROVED
Door Holder Assembly Instructions
III. Catch-Plate Mounting
Electromagnetic Door Holder
READINSTRUCTIONS
Right Wrong
READINSTRUCTIONS
1.750"
44.45mm
1.750"
44.45mm
READINSTRUCTIONS
READINSTRUCTIONS
1.750"44.45mm
Step 1:
With door magnet securely
fastened, aligned and
energized, proceed with swivel
base assembly. NOTE: If door
extensions are required, install
before step 2.
Step 2:
Attach swivel portion of
magnet, being careful to
center catch plate over
magnet.
Step 3:
With catch plate assembly
attached magnetically to door
magnet, peel adhesive
backing off mounting
template and slide over catch
plate, making sure adhesive
side faces door.
Step 4:
Gently close door and with
one hand adjust base of
catch plate to lie flat against
door.
Step 5:
While keeping slight pressure
on door, slide mounting
template over catch plate to
door surface and apply
pressure to template in a few
spots.
Step 6:
Opening door will reveal
mounting template. Apply final
pressure to insure template does
not fall off while assembly takes
place.
Step 7:
Insert alignment template into
center of mounting template. Use
tab to rotate for fine adjustment.
While holding alignment template
with one hand, remove adhesive
backing of tab, then push flat
against door.
Step 8A:
If using optional door back plate,
center punch points indicated on
alignment template for either
horizontal or vertical mounting.
For best results drill 1/8" pilot first,
then follow with 5/16" dia. drill.
Step 8B:
If mounting catch plate assembly
directly to door, drill 1/8" dia. pilot
hole approximately 1 to 1 1/2"
deep, being careful not to go
through door.
Step 9:
For either style of mounting (thru
door/direct) remove only
alignment template, then place
swivel in center. Align holes, then
insert screws and tighten
assembly fully. Lastly, remove
mounting template.
IV. General Dimensions
Door Magnet Dimensions Surface Mount Back Box Dimensions Catch Plate Dimensions
V. Accessories
2.1"5.2 cm
1.2"3.0 cm
4.6"11.7 cm
Backplate
DH-ER1 DH-ER3 DH-BP
2.75"7.0 cm
3.3"8.4 cm 1.1"2.8 cm
1.0"2.5 cm
Extension Rods
3.3"8.3 cm
2.8"7.1 cm 1.1"2.8 cm
0.95"2.4 cm
4.7"11.9 cm
2.5"6.4 cm
2.0"5.1 cm
2.0"5.1 cm
Catch Plate Extension Rod Assembly
E-3627-1098
13047 Rev. C
3.0"
7.6 cm